فراموش کردم
اعضای انجمن(191) مدیریت انجمن طریقه آپلود عکس و فیلم و موسیقی طریقه قرار دادن موسیقی و کلیپ در مطالب
جستجوی انجمن
علی هستم (aliGsm )    

اینم کدهای نوکیا به همراه مدلشون

درج شده در تاریخ ۸۹/۱۲/۲۱ ساعت 14:48 بازدید کل: 2372 بازدید امروز: 123
 

To view IMEI number *#06#
To view Software Version enter *#0000#
To view Status of Sim Clock Stop. Enter *#746025625#
Latest Version is under Phone Info
Type is NSE-3NX
*#92702689# offers you Serial Number and also IMEI number. There are various options to scroll here.
The code is easier to remember as *#war0anty# (warranty)
The next screen is the date of manufacture in the format Made: 1197
The next screen is the purchase date in the format Purchasing Date: 1197 (this can be edited)
The next screen has Repaired: 0000 (presumable at repair the date is entered)
The next screen has Transfer User Data? (the same option as the 8110)
To exit turn the phone off and then back on.
*3370# to activate Enhanced Full Rate (*efr0#)
#3370# to deactivate Enhanced Full Rate (#efr0#)
*4720# to activate Half Rate (*hra0#) ONLY IN SOFTWARE VERSION V4.33 OR EARLIER
#4720# to deactivate Half Rate (#hra0#)
After pressing these codes the phone will shut down and start up again with the service activated/deactivated.
Unlock SP lock
Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!!
Give it a try:
First of all, PIN CODE MUST BE ON, then press:
C

C and hold until it clears display
* and hold until start to blink
* and hold until start to blink
04* * *your pin#
Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON :-(
Anyway it's better than nothing, isn't it?
6110 Sim Card Locking
There are four different types of Sim Locks on the 6110 (not sure about 5110 yet).
1 = Country Lock - Lock to Specific Country
2 = Network Lock - Lock to Network
3 = Provider Lock - Lock to Service Provider
4 = Sim Lock - Lock to Specific SIM Card
To see the status of your phone
#pw+(mastercode)+X#
(mastercode) is a 10 digit number WITHOUT the brackets.
X is a number 1 through 4, it shows the above locks. Not sure of which numbers are assigned to which lock yet. (The numbers above stand for X => for esample: 1 = Country Lock
Sim not restricted message means your phone is NOT sim locked - Check all 4 to be sure.
Most SIMs are locked with the Service Provider Lock => f.e. to the network of MAX

Adding NEW Ring Tones
Set SMSC to +358405202999 (Smart Messaging)
Senf a SMS to 99999 with the word TONES in the message
When you get the reply, edit the message so that the tone that you want does not have a asterisk in front of it. Now send the message to 99999. The phone will display NEW RINGTONE RECEIVED.
Turning on Car Kit and Head Set Menus (Cannot be turned off)
To enable the headset-function, you have to short-circuit the "3" and "4". After a short time there is "Headset" on the display Now, menu 3-6 is now enabled!
To enable the carkit-function you have to short-circuit the "4" and "5". After a short time, "Car" is shown on the display and the menu 3-7 is enabled!!
If you short-circuit the left and the right contact with the middle contact ("3", "6" and "9") the Nokia Software hangs! The profile "Headset" will be activated. Before you do this, just active the "auto call receive" function in the headphone profile and set the ringing volume to "mute" Now you can use your phone for checking out what people are talking about in a room. Place the phone somewhere under a table in this room and call your phone! The phone receives the call without ringing and you can listen to the words these people are talking about!

Nokia 1610

To view IMEI number *#06#
To view Software Version enter *#170602112302#
Latest Version is under Phone Info
Pinouts
Desktop Charger----------------------|

| |

| |

CHARGER--| + TOP OF PHONE -

V V 1 2 3 4 5 6 V

(o) | | [= = = = = =] | |

7 8 9 10 11 12
1 GND Digital Ground

2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.25V...10V - Output Current 50mA)

3 XMIC External Microphone Input and Accessory Identification

Identification

*TYP/MAX: 8...50 mV(The Maximum Value Corresponds to 0dBm Network

LEVEL WITH INPUT AMPLIFIER GAIN SET TO 20 dB ,TYPICAL VALUE IS MAXIMUM VALUE -16 dB)

ID Accessory Identification

*1,7...2,05 V HEADSET ADAPTOR CONNECTED

*1,15...1,4 V COMPACT HANDSFREE UNIT CONNECTED

4 NC Not Connected

5 NC Not Connected

6 MBUS Serial Control Bus

*Logic Low Level: 0....0.5V

*Logic High Level:2.4V....3.2V

7 NC Not Connected

8 SGND Signal Ground

9 XEAR External Speaker and Mute Control

*Min/Typ/Max: 0....32....500 mV (Typical level corresponds to -16 dBM)

Network Level with Volume Control in Nominal Position 8dB Below Maximum

Maximum 0 dBM Maximum Volume Codec Gain -6dB)

Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c.

Mute OFF (HF SPEAKER ACTIVE ): 1,0...1,7 V d.c.

10 Hook Hook Signal

*Hook Off (Handset in Use): 0....0.5V

*Hook On (Handset in Use): 2.4V....3.2V

11 NC Not Connected

12 V_IN Charging Supply Voltage (Max 16V)

Nokia 2010

To view IMEI number *#06#
To view Software Version enter *#9999#
Nokia 2110

To view IMEI number *#06#
To view Software Version enter *#9999#
Latest Version is under Phone Info
Type is NHE-1XN
Unlock SP lock
Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!!
Give it a try
Turn the phone on, when the phone asks for the Security Code,
press:
112
now quickly press:
#
send
end
send
end.
Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON :-(
Anyway it's better than nothing, isn't it?
Nokia 2110e/2110i

To view IMEI number *#06#
To view Software Version enter *#170602112302#
If you have latest software version you have to enter *#682371158412125#
Latest Version is under Phone Info
To view Week and Year of manufacture enter *#3283#
On phones prior to 01/01/96 1295 means December 95, On phones after 01/01/96 2196 means 21st week of 1996.
To enter small letters hold down the key for a few seconds and it will turn caps off

Nokia 2110 Pinouts
Pinouts of X100 system connector
ANT 16 9 Charging connector

(O) I-I-I-I-I-I-I-I ( ) ( o )

CON 8 1
The left symbol (O) is the antenna connector for car kits. The symbol numbered 16-9 on the top and 8-1 on the bottom is the system connector. the ( ) is the open space next to the connector and the ( o ) is the charging connector for you home-charger.

PIN Name Description

--- ---- -----------

1,9 GND Digital ground

2 MIC/JCONN External audio input from accessories or handsfree microphone. Multiplexed with junction box connection control signal

3 AGND Analogue ground for accessories

4 TDA Transmitted DBUS data to the accessories

5 M2BUS Serial Bidirectional data and control between the handportable and accessories

6 HOOK/RXD2 Hook indication. HP has a 100KE pull-up resistor.

7 PHFS/TXD2 Handsfree device power on/off, data to flash programming device.

8,16 VCHAR Battery charging voltage

10 EAR/HFPWR External Audio output to accessories or handsfree speaker

11 DSYNC DBUS data bit sync clock

12 RDA DBUS recieved data from the accessories

13 BENA Power supply to headset adapter

14 VF Programming voltage for FLASH

15 DCLK DBUS data clock
Battery Connector (on the phone)

 

|--|--|--|

1 2 3 4

 

1 ...... GND ground (-)

2 ...... TBAT battery temperature

3 ...... BTYPE -"- type

4 ...... VBATT -"- battery voltage (+)
As you can imagine. YOU CAN DESTROY YOUR NOKIA BY FOOLING AROUND WITH THESE CONNECTIONS. Therefore I accept NO responsibility for any possible damages. My advise to you is to think twice before doing something and if you are going to try make use of a car-kit holder to get access to the X100 connector since it is to tiny to use a self-fashioned connector. IT IS POSSIBLE TO REPROGRAM THE NOKIA 2110 as is indicated by the pinout description so watch it !


DTMF Programming
If you dial in to a service number which requires DTMF strings after you have dialled in, you can program the whole sequence. What you do is:

Key in the number.
Press the * three times: a 'p' appears (pause).
Key in the DTMF code, you can use 'p' again in this string.
Store this in memory.
If you select the memory place, and dial the stored number, the mobile will wait a few seconds (pause) and then send the string as DTMF.
Another option is to press the * four times: a 'w' appears (wait). When the 'w' is reached in the callstring, 'DTMF' appears at the left menu button. When you press the left menu button the mobile starts sending DTMF.
Carkit Programming
If you use a carkit with handsfree AND additional handset, and you want to switch from handset to handsfree:

Press the left menu button, and put the additional handset on hook.
Now you are on handsfree.
Interesting thing to try
As you may know, 2110i supports Call Cost Limit function which means that you can limit the maximum of calls from your phone. This function has a feature that it shows the remaining credits in the third row of the display. It should decrease every time you make a call, but if your operator doesn't support this yet, you can display your phone number or anything else there.

And how to do this? First, go to the "DURATION AND COST" menu. Select "CALL COSTS LIMIT". The phone asks you the PIN2-code, you should get it from your operator. After entering PIN2, select "Set". Phone asks you "Limit:". Enter maximum of seven numbers you want to be visible on display, for example my phone number is 0405100210, so I enter 5100210. So these numbers will be last numbers on display.

And then go to back to the "DURATION AND COST" menu. Select "SHOW COST IN". Enter the PIN2-code. Select "Currency". Enter "Unit price:", I recommend setting it "1". Phone asks you "Currency unit:" Enter the maximum of three numbers or letters or symbols you want to be visible as first numbers/letters/ symbols on display. I entered "040".

Now you are ready. Quit the menu and the number should be on the third row of the display! So, on my display, the last row of the display says 0405100210. It stays there even if you switch off your phone. (Of course it disappears while
you dial a number or use the menu etc.)

Nokia 3110

To view IMEI number *#06#
To view Software Version enter *#3110#
*#92702689# - phone asks warranty code:
There are a number of choices here
6232 (OK) : Displays the Month and Year of Manufacture
7332 (OK) : Displays the date of the last repair
7832 (OK) : Displays the date where the phone was purchased
9268 (OK) : Display Serial Number
37832 (OK) : Set the Purchasing Date MMYY
87267 (OK) : Confirm Transfer, Related to firmware upgrade.
*#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card.
*#7780# restores phone's factory settings.
Type is NHE-8
Pinouts
Desktop Charger----------------------|

| |

| |

CHARGER--| + TOP OF PHONE -

V V 1 2 3 4 5 6 V

(o) | | [= = = = = =] | |

7 8 9 10 11 12
Unlock SP lock
Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!!
Give it a try:
First of all, PIN CODE MUST BE ON, then press:
C

C and hold until it clears display
* and hold until start to blink
* and hold until start to blink
04* * *your pin#
Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON :-(
Anyway it's better than nothing, isn't it?

Nokia 3810

To view IMEI number *#06#
To view Software Version enter *#3810#
Pinouts
Desktop Charger----------------------|

| |

| |

CHARGER--| + TOP OF PHONE -

V V 1 2 3 4 5 6 V

(o) | | [= = = = = =] | |

7 8 9 10 11 12

Nokia 8110/8110i

To view IMEI number *#06#
To view Software Version enter *#8110#
Latest Version is under Phone Info.
*#92702689# - phone asks 'warranty code:'
There are a number of choices here
6232 (OK) : Displays the Month and Year of Manufacture
7332 (OK) : Displays the date of the last repair
7832 (OK) : Displays the date where the phone was purchased
9268 (OK) : Display Serial Number
37832 (OK) : Set the Purchasing Date MMYY
87267 (OK) : Confirm Transfer, Related to firmware upgrade.
*#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card.
Type of Phone is NHE-6
Pinouts
Desktop Charger----------------------|

| |

| |

CHARGER--| + TOP OF PHONE -

V V 1 2 3 4 5 6 V

(o) | | [= = = = = =] | |

7 8 9 10 11 12
1 GND Charger/System Ground

2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.4V...10V - Output Current 50mA)

3 XMIC External Microphone Input and Accessory Identification

Identification

*TYP/MAX: 8...50 mV(The Maximum Value Corresponds to 0dBm Network

Level with input amplifier gain set to 20 dB ,typical value is maximum value -16 dB)

ID Accessory Identification

*1,7...2,05 V Headset Adapter Connected

*1,15...1,4 V Compact Handsfree Unit Connected

*2.22...2.56 V Infra Red Link Conneceted

4 EXT_RF External RF Control Input

Min/Max: 0...0.5V External RF in use

Min/Max: 2.4...3.2V Internal Antenna in use

5 TX FBUS Transmit

6 MBUS Serial Control Bus

*Logic Low Level: 0....0.5V

*Logic High Level:2.4V....3.2V

7 BENA Not Connected

8 SGND Signal Ground

9 XEAR External Speaker and Mute Control

*Min/Typ/Max: 0....32....500 mV (Typical level corresponds to -16 dBM)

Network Level with Volume Control in Nominal Position 8dB Below Maximum

Maximum 0 dBM Maximum Volume Codec Gain -6dB)

Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c.

Mute OFF (HF SPEAKER ACTIVE ): 1,0...1,7 V d.c.

10 Hook Hook Signal

*Hook Off (Handset in Use): 0....0.5V

*Hook On (Handset in Use): 2.4V....3.2V

11 RX FBUS Receive

*Accessory FBUS Receive Signal

12 V_IN Charging Supply Voltage (Max 16V)

Nokia 8810

To view IMEI number *#06#

Nokia 9000/9000i

To view IMEI number *#06#
To view Software Version enter *#682371158412125#
Latest Version is under Phone Info
To view Week and Year of manufacture enter *#3283#

Post by: Arash_142 (Arash Izadkia ) Aras142@ShareMobile.Ws

>>>-----------------------------<<<

All Cod Infomrmation Nokia ! Unlock COD Nokia

*# 06 # Seriennummer/IMEI indicates (actually also a GSM is code - see further below)
-----------------------------------------------------
*# 0000 # SW version announcements (e.g. V3.42.1, 16-10-03, Nhl-10)
---------------------------------------------------------
*# 2820 # Bluetooth (BT) device address indicate
------------------------------------------------------------
xx # Directory quick access (xx = storage location and afterwards lozenge e.g. 24 #)
---------------------------------------------------
A/from key Short pressing for menu for switching between profiles
-------------------------------------------------------------------
Menu key Long pressing for "task manager" - switching between active programs (with "C" key programs can be terminated.)
------------------------------------------------------------------
Menu quick access Over in the menu e.g. to point 3.1 arrive simply 31 enter (if the third symbol a file is opened is for these and then in it started the first Programm/Icon).
---------------------------------------------------------------------
Autostart go around When switching on of the Handys on to the pin inquiry the key "ABC" (pin) comes the whole time keeps pressed - this is to ignore (allegedly) the autoinitialization programs.
------------------------------------------------------------------------
# Do not switch between different lines (AS)... goes e.g. with Austrian ONE Handys (see nose cunning). I could not try out however also, since I did not have 2 lines on the SIM map.
-------------------------------------------------------------------------
12345 ... is according to standard set the Nokia nokia-Sicherheitscode.
--------------------------------------------------------------------
0000 ... is according to standard those (with Vodafone windshield frame section) set 2te pin and that standard net code/password
With D1 the standard net code is the last 4 numbers of the card number without HLR e.g. 99999234-5/55 - > 2345
------------------------------------------------------------------------
0 - for a long time press If one the "0" in the main menue for a long time presses those homepage of the standard WAP connection is called.
------------------------------------------------------
Caution - starting from here the codes are "dangerous"

*#7370925538#
* # of res wallet # ... is to be deleted the code around the "wallet"! Input like normal telephone number (not in wallet code inquiry windows).
NOTE! Afterwards the "wallet" is empty, can again be put on however with new code.
-----------------------------------------------------------------
*# 7780 # The "original attitudes" and telephone re-establishes is again started (an appropriate inquiry and it follow before must the sicherheitscode be entered).
NOTE! Afterwards various "attitudes" are away - among other things these:
·1 Points of entrance (Provider dependent points of entrance and attitudes)
·2 Bluetooth attitudes
·3 Favorite
·4 Allocation of the two keys (beside Navi keys) in the main menue
·5 Profiles are "neglected" (as with distribution) - still there however new bell tones, etc. are...
·6 SMS/MMS/E Mail attitudes
·7 Logos and spielstaende (allegedly) also deleted...
Programs, calendars and contacts, etc. not changed...
Also the sicherheitscode remains.
This putting back goes also via menu under "attitudes - general - original telephone once.".
-------------------------------------------------------------------------
*# 7370 # Soft format: If the Handy (only telephone memory) formats, puts back the attitudes (see * to # 7780 #) and implements a software RESET. (however still another inquiry comes before.)
NOTE! If the Akku to 75% are loaded at least, Akku do not only accomplish during the procedure under any circumstances remove! The procedure takes some minutes (approx. 3-4), is absolutely waiting!
This is "only" a soft format... Hard format with "green, 3, *"... see below.
--------------------------------------------------------------------
Green, * 3 Hard format: If the Handy (only telephone memory) formats, puts back the attitudes (see * to # 7780 #) and implements a RESET.
NOTE! If the Akku to 75% are loaded at least, Akku do not only accomplish during the procedure under any circumstances remove! The procedure takes some minutes (approx. 3-4), is absolutely waiting!

Proceeding: Equipment switch off, which keep "green key" (take off) at the same time pressed, "*" and to "3" key and switch the equipment on (the keys thereby keep further pressed)... to "Formatting" on the display appears...
If that does not function, then equipment for 1 hour switch off, Akku so for a long time rausnehmen and again try.
"only" virtual the memory is generally cleared - genuine formatting can take place only in a Nokia service center, if the Fash is deleted there and/or new L.G. is installed.
---------------------------------------------------------
Mixed * # 92702689 #, then switch - system menu off (goes with me not)

The following code do not fold (with me also):
* EFR0 # (* 3370 #) EFR activate (EFR = Enhanced Full rate Coding - language optimization)
# EFR0 # (# 3370 #) EFR switch off
* HRC # (* 4720 #) HRC switch on (HRC = helped rate Coding - language compression)
# HRC0 # (# 4720 #) HRC switch off
----------------------------------------------------------------
SIM LOCK Simlock status query: (use "*" the key over "p,w" and "+" indications to enter)
# pw+ 1234567890 +1 # Provider LOCK status
# pw+ 1234567890 +2 # network LOCK status
# pw+ 1234567890 +3 # Country LOCK status
# pw+ 1234567890 +4 # Sim Card LOCK status
The code 1234567890 must be computed with a program e.g. SmartDCT4Calc and/or DCT 4 code Calculator from IMEI, etc....
Info. to Simlock: SIM LOCK makes it for the offerer/network carriers possible, subsidized (verguenstigte) Handys to offer. Thus one makes oneself if necessary punishable if one SIM LOCK deactivated - in addition the warranty can purged. I take over for it no adhesion or responsibility!
------------------------------------------------------------------------
GSM code ... should function at each Handy - however Netz(betreiber)abhaengig are... and "harmless"...
Generally applies: First enter code, "send" afterwards (< send green key > press) and one moment wait...
------------------------------------------------------------------
SMS Tipps To Tipps & cheat about SMS (with appropriate codes) are immediately in the FAQ list .
For example for the topic: SMS "retard" and/or deferred send, acknowledgment of receipt, reports...
----------------------------------------------------------------
Mark more simply To Tipps & cheat to the topic "mark" e.g. with SMS entrance.
Over simply to mark simply the "pin" (ABC key) hold some e.g. SMS and move then Jostick downward.
--------------------------------------------------------
Call number transmission * 31 # - { CLIR - Calling LINE identification Restriction switches on for the general call number transmission }
# 31 # - switch off the general call number transmission
# 31 # [ telephone number ] - with the next call suppress the own call number (thus temporary)
* 31 # [ telephone number ] - with the next call transfer own call number (thus temporary)
* # 31 # - status query (of call number transmission)
# 31 * [ telephone number ] - own call number show, although receiving station switched call number suppression on. (is not usually de-energised of the Netz(betreiber).)

* 30 # - switch { TIE-clip - Calling LINE identification presentation for the announcement on of the call number of the caller }
# 30 # - switch off
* # 30 # - status query


http://www.elakiri.com/forum/archive/index.php/t-171323.html

تاریخ آخرین ویرایش مطلب: تاریخ آخرین ویرایش: ۸۹/۱۲/۲۱ - ۱۴:۴۸
اشتراک گذاری: تلگرام فیسبوک تویتر
برچسب ها:

1
1


لوگین شوید تا بتوانید نظر درج کنید. اگر ثبت نام نکرده اید. ثبت نام کنید تا بتوانید لوگین شوید و علاوه بر آن شما نیز بتوانید مطالب خودتان را در سایت قرار دهید.
فراموش کردم
تبلیغات
کاربران آنلاین (0)